GE dishwasher(model#GSD5330D00WW): Motor wasn't running, just humming, found the motor bad.
Here's the motor/pump assembly for this model:
Manufacturer's Number: WD26X10013
Recently in Dishwashers Category
Sears Kenmore Dishwasher(model#363.16121100): Not filling with water. Checked for 120 volts at the water valve inlet with a volt meter, 120 volts present but the valve was not opening up to let the water come into the dishwasher.
Here's the water valve inlet for this model:
Manufacturer's Number: WD15X10003
Frigidaire Dishwasher(model#GLDB957JS0): Not working at all, but the lights are flashing and it was coming on for awhile but shutting down the cycle early. Found the control board bad.
Here's the control board for this model:
Manufacturer part number 154362808 is RepairClinic item number 890302
KitchenAid Dishwasher(model#KUDS01DJWH0): Wash motor just humming, locked-up, found bearing out.
Here's the wash motor/sump pump assembly for this model:
Manufacturer's Number: 8535150
Question on door gasket for GU1500XT - Appliance Blog Repair Forums
Robinh fixed his Whirlpool Dishwasher!
Sears Kenmore Dishwasher (Model#665.16019400) Clean light blinking 7 times. I ohmed the heating element for continuity, no continuity at all from my ohm meter. I installed a new heating element, worked great!
Manufacturer part number W10134009 is RepairClinic item number 1381534
Whirlpool Dishwasher (Model#DU943PWKQ0)
The door handle broke on the dishwasher, Installed new one, worked great!
The color on this one is white.
Whirlpool Dishwasher (Model#DU1100XTPS3)
The clean light was blinking 7 times. I ohmed the heating element out, and it checked ok. The only other part that controls the heating element to cause the clean light blinking 7 times is the control board, I replaced it and problem solved.
This video explains about it:
Our Repair Forum also explains it too:
http://www.applianceblog.com/mainforums/showthread.php?t=5671
Here's the control board for this model:
Manufacturer's Number: 8564546
2005 KitchenAid Dishwasher(Model#KUDI02FRSS1): The control panel console lock light was flashing continually after it washed awhile in the normal cycle, then when the cancel button was pushed, it would drain and then the lock light would start flashing again.
This is caused by a stuck key on the console control keypad assembly.
ERROR MESSAGES
STUCK KEY:
If the control detects that a key is stuck in the depressed position,
dishwasher operation will be suspended and the control will flash
the light for that key until the condition is corrected. If a key without
a light is stuck or multiple keys are stuck, the control will flash the
Lock-Out light.
I installed a new console control keypad assembly, worked great.
Black Console Part#8572494(Black)
White Console Part#8572495(White)
Stainless Console Part#8572496(Stainless)
WASHINGTON, D.C. - The U.S. Consumer Product Safety Commission, in cooperation with the firm named below, today announced a voluntary recall of the following consumer product. Consumers should stop using recalled products immediately unless otherwise instructed.
Name of product: GE Dishwashers
Units: About 2.5 million
Manufacturer: GE Consumer & Industrial, of Louisville, Ky.
Hazard: Liquid rinse-aid can leak from its dispenser onto the dishwasher’s internal wiring which can cause an electrical short and overheating, posing a fire hazard to consumers.
Incidents/Injuries: GE has received 191 reports of overheated wiring including 56 reports of property damage. There were 12 reports of fires that escaped the dishwasher. Fire damage was limited to the dishwasher or the adjacent area. No injuries have been reported.
Description: The recall includes GE built-in dishwashers sold under the following brand names: Eterna, GE, GE Profile™, GE Monogram®, Hotpoint®, and Sears-Kenmore. The dishwashers were sold in white, black, almond, bisque and stainless steel. The brand name is printed on the dishwasher’s front control panel. The following model and serial numbers can be found inside the dishwasher tub on the front left side of the dishwasher.
| Brand | Model Numbers Must Begin With | Serial Numbers Must Begin With |
|---|---|---|
| Eterna | EDW20, EDW30 | SS, TS, VS, ZS, AT, DT, FT, GT, HT, LT, MT, RT, ST, TT, VT, ZT, AV, DV, FV, GV, HV, LV, MV, RV, SV, TV, VV, ZV, AZ, DZ, FZ, GZ, HZ, LZ, MZ, RZ, SZ, TZ, VZ, ZZ, AA, DA, FA, GA, HA, LA, MA, RA, SA, TA, VA, ZA |
| GE and GE Profile | GHD50, GSD40, GSD41, GSD43, GSD46, GSD4910Z, GSD4920Z, GSD4930Z, GSD4940Z0, GSD50, GSD51, GSD521, GSD522, GSD523, GSD531, GSD532, GSD533, GSD535, GSD536, GSD55, GSD56, GSD57, GSD58, GSD59, GSDL3, GSDL6 | |
| GE Monogram | ZBD3500Z0 | |
| Hotpoint | HDA3400F, HDA35 | SS, TS, VS, ZS, AT, DT, FT, GT, HT, LT, MT, RT, ST, TT, VT, ZT, AV, DV, FV, GV, HV, LV, MV, RV, SV, TV, VV, ZV, AZ, DZ, FZ, GZ, HZ, LZ, MZ, RZ, SZ, TZ, VZ, ZZ |
| GE and GE Profile | GHD35, GSD21, GSD2200D, GSD2200F, GSD2200G, GSD2201F, GSD2220F, GSD2221F, GSD2230F, GSD2231F, GSD2250F GSD23, GSD26, GSD27, GSD3115F, GSD3125F, GSD3135F, GSD3200G, GSD3210F, GSD3220F, GSD3230F, GSD33, GSD341, GSD342, GSD343, GSD345, GSD3610F, GSD3620F, GSD3630F, GSD3650F GSD37, GSD381, GSD382, GSD383, GSD385, GSD391, GSD392, GSD393, GSD4525F, GSD4535F, GSD4555F, GSDL122F, GSDL132F, GSDL24, GSM2100F, GSM2100G, GSM2100Z0, GSM2110D, GSM2110F, GSM2130D, GSM2130F | |
| Sears-Kenmore | 363.1438, 363.1447, 363.1445, 363.1448, 363.1457, 363.1467, 363.1475, 363.15161792, 363.1517, 363.1521, 363.1527, 363.1528, 363.1531, 363.1532, 363.1546, 363.1547, 363.1548, 363.1556, 363.1565, 363.1567, 363.1617, 363.1655 | SS, TS, VS, ZS, AT, DT, FT, GT, HT, LT, MT, RT, ST, TT, VT, ZT, AV, DV, FV, GV, HV, LV, MV, RV, SV, TV, VV, ZV, AZ, DZ, FZ, GZ, HZ, LZ, MZ, RZ, SZ, TZ, VZ, ZZ |
Sold at: Department and appliance stores from September 1997 through December 2001 for about $400.
Manufactured in: United States
Remedy: Consumers should immediately stop using the recalled dishwashers and contact General Electric for a free repair, a $150 rebate towards the purchase of a new GE dishwasher, or a $300 rebate towards the purchase of a new GE Profile or GE Monogram dishwasher.
Consumer Contact: For additional information, contact General Electric toll-free at (877) 607-6395 from 8 a.m. to 8 p.m. ET Monday through Saturday. Consumers also can visit the firm’s Web site at www.geappliances.com
Frigidaire Dishwasher(Model#FDB421RFR2): Not cleaning the dishes at all in any cycle. This has been a major issue for Frigidaire for many years now, but they have made a new Motor/Pump Assembly to solve this problem. Its works great!
Wash motor & pump kit
Part#154291501
WASHINGTON, D.C. - The U.S. Consumer Product Safety Commission, in cooperation with the firm named below, today announced a voluntary recall of the following consumer product. Consumers should stop using recalled products immediately unless otherwise instructed.
Name of product: Maytag® and Jenn-Air® brand dishwashers
Units: About 2.3 million
Manufacturer: Maytag Corp., of Newton, Iowa
Hazard: Liquid rinse-aid can leak from its dispenser and come into contact with the dishwasher’s internal wiring which can short-circuit and ignite, posing a fire hazard.
Incidents/Injuries: Maytag has received 135 reports of dishwasher fires, resulting in product and/or property damage. Four injuries have been reported, including three reports of smoke inhalation and one serious hand laceration when operating a fire extinguisher to put out a fire in the dishwasher.
Description: The recall involves Maytag® and Jenn-Air® under counter or portable plastic tub dishwashers. The dishwashers have black, white, almond, bisque and stainless steel front panels. The following model and serial numbers are printed on a label located on the dishwasher’s plastic frame on top of or to the left of the door opening. Consumers should contact Maytag to determine if their dishwasher is included in this recall.
| Brand | Model numbers MUST begin with… | AND serial numbers MUST end with… |
|---|---|---|
| Maytag® | MDB3, MDB4, MDB5, MDB6, MDB7, MDB8, MDB9, MDBD, MDC3, MDC4, MDC5, DWU9 | SM, SQ, SS, SU, SW, SY, SZ, UB, UD, UF, UH, UK, UM, UQ, US, UU, UW, UY, UZ, WB, WD, WF, WH, WK, WM, WQ, WS, WU, WW, WY, WZ, YB, YD, YF, YH, YK, YM, YQ, YS, YU, YW, YY, YZ |
| Jenn-Air® | JDB3, JDB4, JDB5, JDB6, JDB7 | UB, UD, UF, UH, UK, UM, UQ, US, UU, UW, UY, UZ, WB, WD, WF, WH, WK, WM, WQ, WS, WU, WW, WY, WZ, YB, YD, YF, YH, YK, YM, YQ, YS, YU, YW, YY, YZ |
Sold at: Department and appliance stores and by homebuilders nationwide from July 1997 through June 2001 for between $370 and $800.
Manufactured in: United States
Remedy: Consumers should immediately stop using these dishwashers, disconnect the electric supply by shutting off the fuse or circuit breaker controlling it and inform all users of the dishwasher about the risk of fire. Contact Maytag for either a free in-home repair, or a $75 cash back reimbursement following the purchase of a new Maytag®, Jenn-Air®, Whirlpool® or KitchenAid® dishwasher. Consumers should not return the dishwasher to the retailer where it was purchased, as retailers are not prepared to take units back.
Consumer Contact: For more information, contact Maytag Corporation at (800) 675-0535 anytime, or visit the firm’s Web site at www.repair.maytag.com
Sears Kenmore Dishwasher made by Whirlpool (Model#665.17032401): The clean light was blinking 7 times and the dishwasher would not start in any cycle, the only button that would work was the cancel/drain button, but then after it drained it would go back to the clean light blinking 7 times. This indicates a problem in the heating circuit, and the element being bad is usually the main cause. I installed a new one, it worked great.
Part#8563007
Heater element assembly
Maytag Dishwasher (Model#MDB7600AWQ): The dishwasher was making a loud grinding sound, I found a walnut shell in the chopper/grinder filter screen area, I cleaned out the filter/flowplate assembly, worked great.
Part#99003291
Filter & flowplate assembly
Whirlpool Dishwasher(Model#DU910PFGB0): Making loud noise in the wash and drain cycles.
I found all kinds of glass and fruit seeds down in the pump impeller assembly, and the impeller was broken due to all that as well.
Installed new pump impeller kit, worked great.
2003 KitchenAid Dishwasher(Model#KUDS01FKSS01): The control panel display lights were all dead, nothing would come on. I turned off the house breaker to the dishwasher then opened up the control panel by taking off all the inner door screws, that will also release the front outer door panel.
Then I used my volt/ohm meter to ohm out the thermal fuse that's attached to the control board to check for continuity. There was no continuity, so I replaced the thermal fuse assembly with the wiring that was included with it, thats a must, and it worked great.
Sears Kenmore Dishwasher made by Whirlpool (Model# 66515951793): Its stalling in mid-cycle.
Found the control board faulty.
Part#8051136
Electronic control board assembly
Have a good evening!
Area Forecast For: South Willamette Valley
...including cities of Eugene, Springfield, Corvallis
Issued: February 23, 2006 14:23:56 PST
Friday: Mostly cloudy in the morning then partly sunny. A slight chance of showers in the morning. Highs around 45. Light wind becoming north 5 to 10 mph in the afternoon.
Friday night: Partly cloudy. Lows around 30. Northeast wind 5 to 10 mph.
Maytag Dishwasher (Model#MDB7100AWB): When running a cycle and when the the door was closed, there were 4 or 5 lights blinking at the same time. Pressing all of them just to see if it was some kind of error that needed to be reset and it dropped down to two lights blinking. It was a "memory software check" error. It needed a new control board.
Part#99002259
Control Board
Have a good evening!
Area Forecast For: South Willamette Valley
...including cities of Eugene, Springfield, Corvallis
Issued: February 06, 2006 15:05:56 PST
Tonight: Some high clouds early then mostly clear. Becoming mostly cloudy late. Areas of fog after midnight. Lows 30 to 35 light wind..
Tuesday: Mostly cloudy in the morning...then mostly sunny. Areas of fog in the morning. Highs 50 to 55 light wind.
Sears Kenmore Dishwasher made by Whirlpool (Model#6651674992): The dishwasher won't turn off, it keeps running all the time. The timer did move a little bit, but not much. This problem is the dishwasher timer has gone out. The motor that turns the main gear is worn out. It would need a new timer.
Part#3376355
Timer assembly
Here is the repair manual on this dishwasher:
Whirlpool dishwasher repair manual
Have a good evening!
Area Forecast For: South Willamette Valley
...including cities of Eugene, Springfield, Corvallis
Issued: January 17, 2006 14:02:13 PST
Tonight: Showers. Lows 35 to 40. South wind 5 to 15 mph.
Wednesday: Showers and a slight chance of afternoon thunderstorms. Highs around 45. Southwest wind 10 to 20 mph.
KitchenAid Dishwasher Model#KUDA220TWH6
The motor stopped turning, it would only make a hum and click sound when it tryed to start washing. Took the upper pump assmbly apart to the impeller and tryed to turn the motor shaft, but it wouldn't turn. It will need a new motor.
Part#4171577
Dishwasher motor kit
It comes with a spin seal, relay, gaskets and all other hardware.
Have a good evening!
Area Forecast For: South Willamette Valley
...including cities of Eugene, Springfield, Corvallis
Issued: January 05, 2006 15:52:03 PST
Tonight: A chance of rain in the evening...then rain after midnight. Lows around 45. South wind 10 to 15 mph.
Friday: Rain. Highs around 50. Southwest wind 5 to 15 mphFriday night.
