my ignition is off. super capacity 465

[dandyb]

Model No. 6F360BEEZ 0

Every time I turn on any burner the ignitor on the right front clicks -- for all four knobs, they make the right front burner click.
Thus, only the right front will light. Is this the control module?
If Yes, Could you please direct me where I could find a new one.

If not, any ideas?

Thanks.
Andrew

[Jake]

Hi,

Please double check your model#, I can't get any information on that one.

Jake

[dandyb]

The model number is SF360BEEZ 0.

Thanks for your help.

Andrew

[Jake]

Thanks,

Here is a new one for your model:
Spark module, top burners (http://www.repairclinic.com/referral.asp?R=1265&N=905574)

Here is the official repair manual for this Range:
http://adcxns1.whirlpool.com/Service...LE/4322089.pdf (http://adcxns1.whirlpool.com/Service...LE/4322089.pdf)

Jake

[dandyb]

Thanks for the info, Jake.

That module looks a lot different than the installed one. Three prongs at top while the installed on has only 2. The manual site was broken. Anything else?

Thanks a lot

Andrew

[Jake]

Try in the morning for that manual, there site is down.

Jake

[dandyb]

Hi Jake:

I installed a new control module, and the problem is the same -- turn on any knob and only the right front burner clicks. Any advice of what could be wrong?

Oh, that website for the manual is still down and/or doesn't work.

Thanks.

Andrew

[Jake]

Sorry, It was a bad link, this link should do it:
http://adcxns1.whirlpool.com/Service/SrvTechAdm.nsf/2cd44500d572193285256a45004fd9d6/ca8e028c60d9804f85256a8c00621f04/$FILE/4322089.pdf (http://adcxns1.whirlpool.com/Service/SrvTechAdm.nsf/2cd44500d572193285256a45004fd9d6/ca8e028c60d9804f85256a8c00621f04/$FILE/4322089.pdf)

Jake

[dandyb]

Maybe a new ignitor switch on a knob?!?

[Jake]

If all of the burner knobs are making it click, then the switches are ok, I just found a thread thats almost identical to yours, the parts are exactly the same too, actually this member also needed the 3 igniter's except for the right front as well, very ironic, here is that thread:
http://www.applianceblog.com/mainforums/showthread.php?t=2218 (http://www.applianceblog.com/mainforums/showthread.php?t=2218)

Make sure you go to page 2 as well.

Jake

[dandyb]

His problem started with a "cracked" ignitor and needing to replace that because the spark was too low compared to where the gas was released.

My problem almost seems to be some sort of short-circuit and/or crossed wires because every knob activates only one spark ignitor (the front right). If the other 3 ignitors were bad, wouldn't each knob fail to ignite its respective spark at all, rather than shifting over to the front left one and sparking that?

[Jake]

Nope, you probably going to need to contact a local appliance repair shop in your town, sounds like you have more of a technical issue here going on.

Jake

[mhackney]

This was good timing to find this post. I have the same model gas stove. My front right ignitor does not spark but the other 3 do. I just wanted to clarify - when any gas knob is turned to "Ignite", all 4 burners spark (or they are supposed to), correct? In my case, the front right burner does not spark but the other 3 do. In dandyb's case, could it be that the other 3 ignitors are all dead? Did they all fail at once or did this happen over a period of time?

Is there a manual or instructions somewhere on how to replace this ignitor? Is it just pressure fit in to the burner "head" and how do I access the connection at the other end (seems to snake down the back left corner of the stove).

cheers,
Michael

[dandyb]

They went out together after I had to flip a circuit breaker. I thought each knob sparks its own burner. If I had known they all spark, then I would guess my three others have indeed failed. $100 replacement, but it should work, right? I guess you just have one.

Thanks and good luck