-
July 22nd, 2008, 01:50 PM
#1
Ice not ejecting
First time poster here, please help me before I pull my hair out! I have a Kenmore Side By Side friderator, Model# 106.56576400. The icemaker stopped making ice, I've replaced the icemaker and the water valve, I got 4 cycles of ice after 2 days of installing the icemaker and now there is ice in the mold but it won't eject into the bucket. The ejector is laying facing to the front of the frigde. I did the sensor light test and I get the 2 flashes then off for a second and 2 more flashes. When I hold the emitter door flapper in, The light continues it's cycle of 2 flashes then off for a second and 2 more flashes. I've unplugged the fridge and plugged it back back in and still get the same flashing cycles as stated above. Please HELP!!
-
July 22nd, 2008, 10:13 PM
#2
Hi,
Ok, from the chart I posted awhile back here, it looks like your optics are bad.
Ok, I have my chart here for the Ice Maker Blinking Codes:
Step#1: Open the freezer and view the status led
(STATUS LED)
2 BLINKS FOLLOWED BY 1 SEC. DELAY(REPEATED)
POSSIBLE CAUSES: The flapper door on the emitter is blocking the beam or the optics are faulty.
Step#2: Press the emitter flapper to unblock the optics beam
(STATUS LED)
2 BLINKS FOLLOWED BY 1 SEC. DELAY(REPEATED)
POSSIBLE CAUSES: The optics are faulty. Replace the emitter and receiver boards.
Here are the boards you can order, they come together in 1 kit with instructions:
P.C. Board kit, emitter & receiver
If the LED is on steady: The optics are working properly.
Jake
Appliance Repair School 1987-1988
Star Appliance Tech. 2 yrs. 1988-1990
Wards Appliance Tech. 11 yrs. 1990-2001
Sears Appliance Tech. 4 yrs. 2001-Oct. 2005
Jake's Appliance Repair Nov. 2005-present
Look-Up & Order Parts
-
July 25th, 2008, 07:31 AM
#3
I oredered the emitter and receiver boards, should be here today. Funny thing, the icemaker made 3 batches of ice yesterday and doing the test on the optics, it was normal with the solid red light staying on, however, after the 3 batches of ice, the icemaker filled and froze in the mold but did not eject, so it's back to how it was when I first posted the problem, could it still be the emitter/receiver boards? Thanks
-
July 25th, 2008, 09:36 AM
#4
Yes, it sounds like they are intermittently working/not working.
Jake
Appliance Repair School 1987-1988
Star Appliance Tech. 2 yrs. 1988-1990
Wards Appliance Tech. 11 yrs. 1990-2001
Sears Appliance Tech. 4 yrs. 2001-Oct. 2005
Jake's Appliance Repair Nov. 2005-present
Look-Up & Order Parts
-
July 25th, 2008, 02:47 PM
#5
-
July 26th, 2008, 06:14 AM
#6
Thank you JAKE, I received the emitter and receiver boards, installed both in 10 minutes and all is working well, I have ICE! Thanks Again for the great service.
-
July 26th, 2008, 09:13 AM
#7
Excellent VC-17, good job fixing it.
Jake
Appliance Repair School 1987-1988
Star Appliance Tech. 2 yrs. 1988-1990
Wards Appliance Tech. 11 yrs. 1990-2001
Sears Appliance Tech. 4 yrs. 2001-Oct. 2005
Jake's Appliance Repair Nov. 2005-present
Look-Up & Order Parts
Similar Threads
-
By speedway in forum Frigidaire/Electrolux
Replies: 17
Last Post: December 8th, 2008, 12:26 PM
-
By kbert in forum Frigidaire/Electrolux
Replies: 3
Last Post: July 20th, 2008, 11:02 AM
-
By makiman in forum Sears Kenmore
Replies: 20
Last Post: April 26th, 2008, 06:00 AM
-
By Hookem in forum KitchenAid
Replies: 1
Last Post: February 2nd, 2008, 04:05 PM
-
By NDS in forum Whirlpool/Roper/Estate
Replies: 10
Last Post: July 27th, 2007, 12:23 AM
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
If you feel that you have benefited from this site, and would like to show your appreciation, you can throw a buck or two in the Appliance Blog Tip Jar - Thank you!
Reply With Quote
