1. L

    Maytag Bravos XL Washer MVWB880BW0 has loud spin cycle and clacking during agitation

    Hello Just got this washer used and it's got a loud spin cycle that I assume is the bearing, but also during agitation it makes a loud click/clack noise at either end of the agitator's turn. There's a video of this attached. Any thoughts on what I need to do to get things running right?
  2. R

    GTWN4250M1WS GE Washer - Makes a racket spinning, Should I replace everything?

    I have a GE top loading washer GTWM4250M1WS. It makes a racket spinning. I'm going to attempt changing the WH38X10017 Shaft and Tube Assembly. Am I correct in assuming this is the more likely faulty part? I'm not confident I can just do the bearings part of this. And I can get that part for...
  3. P

    NVL333EB6CC Hotpoint Drum won't lift out

    I'm trying to remove the drum to replace a noisy bearing, but after loosening the belt, the drum will not pull out. I've removed the 3 screws in the back of the drum and pulled it out that way, but the plate is still stuck on the bearing. Any thoughts?
  4. A

    LWS34AW Speed Queen Washer Tub Seal

    Im Looking for a tub seal for the a Speed Queen washer It seems the part has been discontinued and I was wondering if there is a alternative part. The original part# is 40016101. Any help will be greatly appreciated, thank you.
  5. T

    DCVH515EF0WW GE DRYER - New top front bearing and slides keep wearing out.

    Hello, My dryer was making a screeching sound when running. I replaced the idler pulley, belt, rear bearing, top/front bearing and slides. After about a month of use, it started screeching again. I opened it up, and found that the top bearing and slides were wearing very uneven (see attached...
  6. C

    MHWE201YW00 Sourcing outer tub with bearing for Maytag

    Howdy -- We have a Maytag MHWE201YW00 that ran in to problems. I identified the issue as the bearing in the outer tub and sourced a part online (part # W10285625). The shipped part ($210) had a totally rusted bearing:
  7. T

    FIXED MVWB750WQ0 Problem Installing Bearing and Seal Kit in Maytag Bravos Washer

    Everything was going smoothly. Used the recommended bearing press tool to install the bearings. I installed the new drive shaft. Used a hammer and block of wood to ensure the drive shaft bottomed out on the top bearing. Instructions said to "tap" with hammer. It required a few strokes a bit...
  8. W

    Noisy during spin cycle - Frigidaire Stackable FGX831CS0

    Hello. During the spin cycle of this top-load stackable unit there is tremendous noise. I have read a few replacement parts sites that suggest it may a bearing, or a support. I am a limited DIY person (toilet, microwave light sockets, etc). That being said, I most likely will not do the repair...
  9. X

    FIXED IJ4100 Inglis Washer Grinding noise while spinning

    My washer is a Whirlpool Inglis IJ4100. The machine has started making a grinding noise when it starts spinning, but the noise dissipates when it's spinning faster, and it is quiet while agitating. I'm thinking it might be the bearing, but would appreciate any help with identifying the issue.
  10. W

    FIXED WTW6800WW1 Whirlpool Cabrio Washer First, F54 Now F50, F51 and F72. Bearings replaced last month.

    Whirlpool Cabrio Washer First, F54 Now F50, F51 and F72. Bearings replaced last month. In May I got tired of my Whirlpool Cabrio throwing constant UL errors during the spin cycle so I sent away for a new bearing kit and repair tool. I repaired the unit successfully on June 1 and it ran well...
  11. K

    Stuck at replacing seal in LG front-load washer

    I have replaced the two bearings and am trying to get the seal in. I am unable to great the seal to seat in behind the bearing. Tried using soap tapping with mallet, pushing with thumbs. It keeps popping up on the opposite side you are pushing on.
  12. N

    Black grease stains on clothes and noisy washer

    So I have been reading around these forums and I wanted to post here for confirmation. Our clothes are getting ruined in our washer with black stains and smudges all over them. It looks like grease stains. Also, my washer sounds like it is about to take-off and fly the friendly skies during...
  13. D

    kenmore washer repair ,417.43142200, Question

    long story I was at my buddy's and his wife started a wash load I said that thing sounds awful like a bearing going out or sumthin a week later he says to me he is getting a new washer repair guy said main bearing was bad and get new washer ... I asked if all else was working well and could I...
  14. S

    Brand New Frigidaire Dishwasher - Loud grinding noise

    Last month I purchased a brand new dishwasher, Frigidaire model DGBD2432XFI. It ran quietly for 2 weeks before a very loud grinding noise / squeal started coming from the motor. The noise gradually became quieter and turned into a groaning type noise...almost like the sound of a horn on a Model...
  15. D

    [FIXED] Loud spin cycle brown liquid leak

    I have a model MAH5500BWW washer that gets about 25 loads per week and was purchased in 2002. The washer has been making loud jet engine type noise and vibration during spin for the last few months. When I opened it up These photos show what I found. Neptune Repair pictures by dfsolander -...
  16. C

    Repairing rear bearing on Gallery GLTF1040ASO?

    I have an opportunity to purchase a matching set of Frigidaire Gallery Washer/Dryer Set (Washer Model is GLTF1040ASO, Dryer is GLEQ332AS1). I have yet to visually inspect the units, but the owner states the rear bearing on the washer is going out. But he was also told by someone else that the...