cabrio

Hello, recently we have been having issues with the dryer thermal fuse failing. We replaced it numerous times and ended up bypassing it to get the dryer to run but then it was getting too hot. We read on here to replace the dryer heating element per a previous post. When we took out the old one...

After some research, I found that my Whirlpool WTW8500DC0 was displaying an F7E5 error code. I replaced the clutch coil and checked all the gears, wiring, and parts for wear. Everything looks good. Now the washer will work fine with no clothes in the tub, but if I put more than a few items in...

hello, my whirlpool cabrio washer, model WTW5500XW3, recently stopped working. it refused to fill, and would just sit there and impotently grind and do nothing. it gave off a code saying the drain pump was the problem. here is what that looked like: https://photos.app.goo.gl/WB7E1cHuqoy696L8A...

My WTW7000DW0 just keeps going through the wash cycle over and over again. Keeps giving me balancing error. f0e3 and f035 keep coming up. Checked drainage, springs, everything I could see without taking out the tub. I'm able to run the spin manually but today I noticed frothing all over the...

Hello! I have a 10 year old Whirlpool Cabrio WTW5640XW0 washer with some kind of leak. I recently started noticing a burning plastic smell after running a wash load. Searches led me to believe it might be the capacitor. I looked around the machine, but never noticed anything that looked out of...

Hi there, I recently ran into an issue with my Whirlpool Cabrio washer. Upon attempting to do any task with the machine will result in the washer engaging the lid lock and stopping indefinitely during the sensing phase after disengaging the lid lock once more; I do hear what appears to be the...

Hi Everyone, So, here's my sad tale of woe. About two years ago, I got an F50 fault. I pulled the washer, checked everything, cleaned the leads, and everything seemed to be fine. Last week, I got an F50 again about 45% through a wash cycle. Again, I pulled the stator. . .and then I had this...

Lid locks, bucket slowly turns, doesn't fill and shuts down. The agitator did not move freely. Error code F7E5. Cleared and ran diagnostics, everything worked well except the spinning/agitation. Voltages checked out. Replaced the drive assembly. Ran the calibration, and same error now. What can...

I've put it in diognostic mode, got error F9 E2 but i'm not seeing anything wrong with the drain? it just started happening out of nowhere, it just spins and spins and spins way longer than needed, then when done there is water at the bottom. Drain seems to be working cause water comes out just...

Hi All - Appreciate the help with improving my mechanical skills! First some background info, In the beginning, I gathered up at least 2 spare Cabrio WTW6600SW1 washers as they were unfixable for many, and they were selling them for either nothing or like $50. I stripped one and kept one in...

Hi, I believe I had the same error code that was covered by the warranty a few years ago but I don't know if this is the same problem coming back or a new one related to the same F50 error code. The washer locks, starts pulling water into the basket, stops, starts pulling more. Pretty much like...

<b>Whirlpool Cabrio WTW7600XW2 </b> The drain pump on my Cabrio washer will not stop running. When I run the automatic diagnostic test it gets stuck on step C8. I've got an overload error code on it, and I've blown out the pressure tube. I've also did a pressure transducer calibration. The inner...

Hi I looked on the internet about replacing the bearings on the washer. this would solve the spin noise issue. I started the repair but can not remove the nut (1 1/4 inch) at the bottom of the unit to remove the basket, bearing, spindle/shaft. Additionally I can not remove the wash agitator...

Hello, My Whirlpool washer model #WTW8600YW0 has developed a leak in the front left of the machine, location verified by placing cardboard under the machine and observing the drop spots. I'm not sure what water sources are in this area of the machine, perhaps the laundry soap dispenser? I just...

Whirlpool Cabrio Washer First, F54 Now F50, F51 and F72. Bearings replaced last month. In May I got tired of my Whirlpool Cabrio throwing constant UL errors during the spin cycle so I sent away for a new bearing kit and repair tool. I repaired the unit successfully on June 1 and it ran well...

I need some advice on fixing the F51 error code on my Cabrio washer. (Model WTW6600SW2). I have replaced the bearings and shaft (which needed to be replaced a while ago anyway), replaced the rotor position sensor, AND the stator. Still getting the F51 code! When I try to put it in automatic...

My wife said that the washer was much louder during the final spin than normal. Also, said it sounded wrong during the wash cycles when it would spin. She described it as clunky or scrappy if that is of any use. I'll link a video to the final spin just as it is finishing. We have 3 kids and...

I have been reading the forums and trying to figure this one out. My washer will start a cycle but will fail on during the second sensing cycle. Motor humming and you can feel the basket spin down. The lid lock led will flash. I have run through the diagnostics and it doesn't give me a...

Hello all, sorry if I'm intruding or anything, I didn't know if this forum had a introduction section or not. I have a Whirlpool Cabrio (M# WTW6500WW1) that had the F51 error. I had tried the manual spin to see if the RPS's worked, and at first they did. All 3 lights lit up as I spun the tub...

I have a Whirlpool Cabrio WTW6200SW0 washer. I was getting an F1 and the diagnostic mode showed a F1 followed by 68. I replaced the main board. The washer worked for about a week but at the beginning of every cycle I would get a LF. I would hit start once and it would complete the cycle. This...