control board

  1. F

    GE Profile inconsistent cooling on both sides

    My GE Profile side-by-side has been cooling inconsistently on both sides - but more so on the freezer - for almost a year now. The temperature will rise to anywhere from 8 to 15 degrees on the freezer (setpoint at 0) and 40 to 48 on the fridge (setpoint at 37), much like it might do during its...
  2. R

    RE: Icemaker leaking

    RE: Icemaker leaking In the closed thread http://www.applianceblog.com/mainforums/whirlpool-roper-estate/13804-fixed-whirlpool-icemaker-leaking.html Jake replies to katabell in post #8 "Ok, in your case its a little different, when you lift the arm that just turns the ice maker off, thus no...
  3. C

    Jenn-air JDS9860AAP Oven won't turn on

    My Jenn-air's oven won't turn on. I set the oven function (bake, broil, or convect) and the temperature. I hear the relays clicking (once for element start, a few seconds later for fan) but the element stays cold and the fan doesn't go on. I'm pretty sure a relay in the control board has gone...
  4. A

    PSC23PSTA GE Refrigerator STILL not cooling after replaced motherboard

    Hi all - After browsing the forums on here, I ordered the control board for my GE Artica Refrigerator, model # psc23psta. It is 6 years old. About 2 years ago, I had an issue with the same fridge where BOTH sides (the fridge and freezer) did not work. A GE technician replaced the control board...
  5. K

    FIXED JGS8750CDS00 Jenn-Air Range electronic panel does not work

    The burners work fine but we cannot use the oven or set the time as the control panel buttons do not work. Apparently this is a common flaw with Jenn-Airs and the board needs to be replaced every few years. How can I confirm the problem (board [part 8507P227-60] or membrane [part ??])? How do I...
  6. W

    Stuck on 2-minute drain

    No matter which cycle is selected, when I press Start/Resume (S/R), dishwasher goes into 2-Minute Drain (2-MD). Pressing S/R again turns off 2-MD. Pressing Cancel/Drain (C/D) also starts 2-MD; C/D again turns off 2-MD; and so on with both S/R and C/D act as toggle for 2-MD. I can not start any...
  7. B

    FIXED Freezing Mystery

    Sorry for the lengthy story, but I'd rather give too much information than to little to help any experts around here to diagnose and help! My Story: So I have a spare fridge that is in my back room used to keep wine and beer in mostly. It broke a while back and I had to replace the control...
  8. M

    Maytag Neptune control board acting up

    My dryer started to not respond to keypad presses somewhat erratically. Now it won't start up at all, and mostly shows "18" on the LED, although occasionally I'm able to get the timer button to function and add time to a timed dry, but still can't start the dryer. Opened up the rear service...
  9. A

    Bosch DW SHX will only run for a few mins

    Hi everyone! First time poster. I am a repair tech with three years experience, not very long I know, however, I do consider myself pretty good at most things but I have a problem with a bosch SHX4AP05UC/02 dishwasher. Origonal complaint was the customer said that it would turn on, run for a few...
  10. D

    Kitchenaid Built-in Side by Side Refrigerator Fan Not Turning

    Hello, The fan to our KitchenAid Side by Side Built In fridge was not running, the door trim was hot to the touch. We replaced the fan and it turned on, however, after a while it stops running even when the condenser is on. A test with the voltmeter indicated that there were no electricity...
  11. S

    No lights on the control Panel.

    I have no lights on the control Panel of my Mic. The fuse and switches check out fine. I have voltage coming to the circuit board but I am not sure where and how much should be on which wire. I don't want to waste my money so before I go ahead and order a control panel, is there way to determine...
  12. J

    Frigidaire Affinity stops upon arriving at the spin cycle E43

    The machine stops upon arriving at the spin cycle. When you put the machine in "spin only" it runs for 1 minute then shuts down regardless of the speed setting. I checked and got E43. I was told to change the door lock switch, which I did, but am still having the same issue. I also been told it...
  13. T

    Kitchenaid KSSC48QMS Built in not regulating temp

    I noticed that my icecream was soft so I checked the freezer temp and it as at 17 degrees F. The next morning it was reading 0 F however the icecream was still soft. Temp on the panel is not reading correct since feeezer is still at 16 F. Appliance repairman stopped by $106 diag. He claimed...
  14. O

    Whirlpool Range control board short

    I was wiring the range plug into the circuit panel. Forgot to check if the range was plugged in and it was. While pulling the wire into the panel the ground wire hit the 120 buss and sent current back through the ground tho the stove. I thought the control board got shorted out so I ordered a...
  15. S

    FIXED Dryer Issue - Control board ?

    I own a Whirlpool gold (gas) dryer for the last 10 yrs. The dryer has stopped working. When I press the start button, it just beeps but does not start. I tested most of the fuses etc after researching online. I concluded that the control board has gone bad. I replaced it. The dryer started...
  16. T

    kitchenaid slide-in gas range touchpad not working

    Kitchenaid slide-in gas range, model KGST300BWH1, installed in 1996. Just started renting the house in August, when we left in July, the oven worked perfectly. Then, the oven control started working intermittently and after troubleshooting, determined the board had gone bad. I suspect the...
  17. A

    How Do I Measure These Control Terminals

    I have an American Standard Freedom 95. I see it has PCB points to measure "Cool", "Low Heat", and "High Heat". The PCB has two holes per hole that are soldered shut. I tried measuring between the holes with a volt meter looking for AC and DC voltage but didn't see anything. My understanding...
  18. B

    kenmore (#417.84152500) not heating, now not doing anything

    now its time to turn to the pros...have been troubleshooting my dryer, which would turn on, tumble, blow but wouldn't heat. tested the thermistor, high limit thermostat, thermal limiter, voltage coming in. thought i found a bad thermistor. replaced and it did not fix the issue. figured it...
  19. S

    KA electric oven broil, bake elements don't heat

    Hi, and thanks in advance for all the help you provide. I could not find help for a similar sort of problem in the Kitchenaid forum, so I'll post a new item. This slide-in range has power, and the stove-top works fine. For no apparent reason, however, the oven stopped working recently. I had...
  20. O

    expierienced electronic tech need help

    Hi I have an asko condenser dryer, that is getting no power. asko is a brand out of sweden and this thing is just strange and hard to work on but, I changed both buss fuses in the back, also the thermal cutoff button was out, so I depressed it, none of this fixed the problem, I was able to get...
Top