grinding noise

  1. G

    FIXED Maytag Centennial MVWC300VW1 Clutch Bad?

    Hi Folks, I'm new to the forum. My Maytag Centennial sounds like the agitator is slipping and not rotating as much as it should during the wash cycle. It's also quite loud as you can see in the video. The clothes are not really spinning too much either. I've read that the clutch may be...
  2. S

    FIXED WTW5000DW1 In wash mode plate doesn't move and has grinding sound

    My washer started this yesterday the plate doesn't agitate and I heard a grinding noise in the wash cycle, it will advance to all other functions until done then shut off as normal. I removed the plate (has already been replaced) also checked the hub (also replaced) both do not look worn down. I...
  3. D

    GDF520PGJ0WW Video: GE Dishwasher Grinding Noise

    I have a GDF520PGJ0WW that makes a grinding noise. It is about two years old. After observing a few cycles it sounds like it only happens when it pumps. Here is a video... https://drive.google.com/open?id=0B9...VQ2ckkzMDVJaDA I'm guessing I need a new drain pump. Any second opinions? Part...
  4. J

    FIXED Frigidaire GLRS237ZA Not Dispensing Water Properly

    Hi all, It doesn't appear to me that this problem has already been addressed. We re-built our house and I recently brought our refrigerator back in from outdoor storage where it saw temperatures varying between summer heat down to winter freezing. The water inlet valve broke on the move so I...
  5. M

    Frigidaire Gallery Ice Maker Trouble

    I have a Frigidaire Gallery refrigerator with a JBND-26 Ice Maker. I think it's about 4 or 5 years old, but I don't know if the previous owners bought it new or used (it came with the house that my husband and I bought in 9/14. At first it was all working just fine. Then a few months ago we...
  6. E

    FIXED SHX7ER55UC/50 Grinding Noise mid-cycle

    Hello, I've been using my dishwasher regularly for over over two years. Yesterday, mid-cycle on normal wash, a noisy grinding sound came from the dishwasher. The countertop even started to vibrate! I cancelled the wash. I then restarted it and towards the end of the wash (about 20 minutes...
  7. J

    FIXED Kenmore 80 series will not start

    Dryer will not start when I push the start button. There a grinding noise coming from behind the control panel when i push the start button. The light inside the dryer works that it. Any clue what it might be? Thanks
  8. L

    FIXED WTW4950XW Whirlpool Top Load Washer not wanting to spin

    When the washer goes into the spin cycle it sounds like it is slipping or not catching. Not sure if it would be a Splutch assembly or is it the transmission. How would I know which it is?
  9. J

    Maytag performa grinding sound while washing..spins fine

    I have a Maytag Performa PAV3300AWW Rev 12 Serial 12038249ZF that while washing makes a horrible grinding sound in the same cadence as the agitator. Eventually the agitator stops but the grinding sound continues. It sounds like metal gears that are stripped or grinding on each other. Could it...
  10. A

    Kenmore 70 Series Dryer Making Grinding Noise

    My Kenmore 70 series Dryer makes a terrible grinding noise. I first noticed that the grinding would happen only for a couple of seconds after I turned the dryer on, but now its consistent. I don't believe it is the motor, because I manually spun the tub with my hands with the dryer off and could...
  11. L

    FIXED DIY: How to replace your Maytag Washer Drain Pump

    Hi All, Figured I post this since I just ran into this problem and it was a no brainer once I used this site to track the issue down in a previous thread I read. So here is the a little DIY I created, I would rank this a 2 out of 10 on the difficulty scale. Problem: Grinding noise only when...
  12. J

    GS5SHAXNL00 Another Whirlpool icemaker with a problem

    I have a Whirlpool Gold Conquest side by side with an icemaker on the fritz. Change the filters religiously, have a water softener, but still I have a problem. Lately, the icemaker is making a small grinding noise and no ice. I did the LED test and that tested ok. Is it time for a new...
Top