neptune

I have a Maytag Neptune gas drier model #MDG9700AWW. The timer advances but gets stuck at 1 minute left, this happens on every setting, timed or sensor dry. The drier does dry the clothes and the heat shuts off but the timer shows 1 minute left and the drier continues to run. Any ideas would be...

I have an older Maytag Neptune Gas Dryer MDG9700AWM I’m having issues with. We just started having issues where it wasn’t getting warm and drying the clothes. I tore the dryer apart to check things out, dryer vent is super clean and close to the outside wall so good flow. So the dryer starts...

I have a Maytag Neptune Stacked Gas Center. It's a great model and does good work, unfortunately recently it stopped working. I'm a father of 5, and we use unit heavily, but it's a work horse and love it. The issue with the unit is that when you put towels inside, I turn the knob to heavy, max...

Hi have an almost 20 yr old stackable Neptune that has been a decent reliable machine. When i turn the dial to the start of the wash cycle and press the start button, the machine fills, the lights for operation go on, it agitates and the lock engages and light goes on---but then about 5...

I bought a used MLG2000AWW Neptune stack unit and it needs a new washer door seal. Wondering if anyone has a used one they'd like to sell? Trying not to spend another 125$ for one. Paid 200$ for the stack unit and everything works but the door seal is pretty bad. Thanks. Part Number...

Alright so, I recently replaced a part, it was the thermister for this washer because it was getting water in the machine after the cycles were over leaving the clothing wet, Well... that worked, the replacement is great but now, the machine is just spinning forever in a cycle. Even in the...

I have a older Neptune Stack that the washer portion has stopped working. Ran a load last night and it finished normally. Put the load in the dryer and the dryer started just fine and is drying the clothes. Put a load in the washer and hit the start button and nothing. Usually the ON light...

It's inconsistent, sometimes it stops early in the cycle, sometimes later. When it does, it's completely off, need to push and hold down the power button to get it to start again. Eventually it's able to complete the load. I have already opened it up and checked: R11 resistor is fine, already...

I have a Maytag Neptune MDG9700AWW gas dryer. The machine is about 15 years old. Recently It can't seem to heat up air. The igniter glows red, ignites gas, but the flame quickly subsides. About a minute later, the cycle repeats. The air is not even warm. What I have done: 1) Air vent was...

Hi All, I have a Maytag Neptune MAH3000AWW. I had a issue back in February with hot water intake and replaced the control board which fixed the problem. Now I have a new problem... The machine doesn't spin fast and seems to make a growling/groaning noise whenever it "tries" to spin fast...

I have dual cabinet gas dryer that works in diagnostic mode and shows error code of stuck button. Can't tell which button(s) because all lights don't go out on button test. I suspect Start button, but not sure. 1. How to determine if or which buttons are stuck, especially Start button. 2...

When I start a normal wash the washing mashing will fill up with water, but when the agitation disks are supposed to start spinning I hear some noise but nothing happens, and the timer just counts down. When I try to put the washing machine in a service mode "quick spin test," I hear some...

The 12002039 motor conversion kit diagnostic check (removing JP4 and powering up the motor/control) results in a repeated cycle of: 3s of rotation at approx 50 rpm and then 30 s of no movement. The expected result is a continuous rotation at 50 rpm. What could be the cause? The incoming 120...

SN: A2952759CC. I have researched this model and its many inherent problems, and studied the repair manual. However, my problem doesn't seem to correspond with the common issues. The washer seems to cycle appropriately, and perform all fill, wash, rinse, and spin functions. However, it hangs...

Does anyone know what would cause the ignitor to burn out? I replaced the ignitor in my dryer a few weeks ago and the new one just burned out. When I purchased the new ignitor I watched the parts store open and inspect the new part (he never touched it), I was also very carful not to touch it...

The dryer has been beeping randomly, occasionally will work, but less and less frequently. Now it is stuck with sensor dry lit, 54 minutes on display, sensor dry button works, but all others don't, and it isn't starting. I checked some advice. Jake gave someone in other threads about a...

Have read many posts on this machine, all have been some time back, older posts. Have not been able to find any manuals, diagnostics for this model. There is not one located under the panel, guess someone was there before and didn't replace it. Don't know the age, it has been a decent machine...

I replaced the struts in my Neptune a few weeks ago and still no improvement on the out of balance issue. I took a video of what it does during the spin cycle today and would like to know what you guys think is the problem. All that was in the washer was a few sheets and towels. It does this on...

Got home the other day and wife told Me that something was wrong with dryer. When I went to look at it all the lights would come on, on the display, but when hitting start nothing happens. Thinking back to the people at work that say " unplug it and restart" after I got nothing there I left it...

Similar problem to Thread 35047. May tag dryer starts and fires up normally. Heat cuts off after 1-2 minutes. Checked exhaust vent, Lint filter air vents and tubing to outside. Cleaned moderate amounts of lint, but problem persists. Took off front panel. Heating coil glows bright red...