samsung dryer

Samsung dryer, DV45K6500EV/A3. Select cycle, press start. Drum doesn't start turning, but display reads as if it has (timer starts, indicator for "drying" blinking). After about 15 seconds, there is a very quiet *click* coming from the machine, and about 20 seconds after that, the display...

I looked online before posting but couldn't find anything. I have a Samsung DV42H5000EW/A3 dryer that's not blowing any hot air. I already replaced the heating coil and the thermostat. The dryer starts up normally but no heat comes out of the dryer. I keep seeing that you can diagnose the dryer...

My Samsung Dryer has been showing this sign while drying. I have searched and searched if it was an error code but i cant find anything. Has anyone else had a problem like this? It still dries my clothes and works just fine, didn't know if its something i should be concerned about or not. thank you

Hi there, I bought a house recently and the Samsung DV48J7700EW/A2 had been purchased and installed by the previous owners. I have been using it for several months now. In the last couple of months, I noticed that the power button was "mushy". It was hard to press down, it seemed like the...

Hi everyone, I have a Samsung dryer model: DV42H5400 that shuts off after 2 minutes on a sensor setting. Manual settings are fine and continue to dry. So far I have tested and/or replaces the following: 1. Thermostat and temperature fuses - replaced, the issue still persists. 2. Removed the...

Brand new Samsung DVG45R6300V dryer motor bushing is loose and causing clunking/rattling sound when dryer runs. How do I secure this part? Thanks in advance!

Unit would begin a cycle, within a second or two the machine would pause then start again a few minutes later only to stop again. This cycle would continue until the time "ran out". This behavior was present on timed as well as sensed drying cycles. After researching I tore the machine apart to...

Full model @ is DV365ETBGWR/A3-0001. Samsung gas dryer manufactured in October 2013. Went to dry a load of clothes. Pressed the power on/off button and the front panel did not light up as usual. Everything was totally inoperable. Checked power outlet, power cord as it enters the dryer, the...

Hey everyone! I have a samsung dryer model DV42H5600EP that no longer has any heat, but still runs. Airflow is good so I tore the dryer apart and started testing things -power to dryer measured 240v -thermostat checked out -high limit checked out -tested the heating element and showed...

I notice that when I use the "refresh" cycle or any cycle that uses the connected water for steam, there is a puddle of water on the floor by the front right corner of the dryer. At first I thought it was perhaps the hose loose at the back, but if that was the case it would leak all the time...

Recently my fairly new (bought in April 2015) Samsung dryer has been getting noisier, and starting today has gotten a lot worse. At first today it was making squealing noises, then kind of a grinding noise which to me sounded like belt slippage, then the last load I just put in it is a very...

My Samsung dryer runs through its full cycle in every mode but at the very end of each cycle it ends with an HE code. When I get the clothes out they are dry but hot like they didn't cool off during the cooldown cycle even though it says it's doing the cooldown cycle. The technician checked...

Hi all - HELP! After reading through the forums I figured my problem should be easy enough to solve. I've got a barely used Samsung DV36J4000EW/a3 that I bought two years ago for my seasonal home that had started to act up. At first, the dryer would run for 20-30 minutes, before stopping with...

Hi everyone, i'm new here and need help. My Samsung washer 18 months old (i'll never purchase another samsung product again!) just broke 2 days ago and we had to buy a new one. Today my Samsung dryer also 18 months old has done the same. I'm attempting to fix it myself because I cannot afford a...

DV42H5000EW/AC Heater works during test mode (Press "Adj Time up" + "Temp", LCD displays "SC", Press "START"). All PCBs, thermistor, and moisture sensors changed. Dryer is clean and shows no other symptoms. No error codes. Resistances of both sensors (thermal and moisture) measure OK. This is a...

Lately, I've been trying to be a DIYer, but this one has already taken 6 hours between research and labor. I've completely taken apart and ohmed all fuses, thermistors/stats, and solenoids, everything checks out fine. They igniter is good as well. I do not see a traditional heating element/coil...